Vbrick-systems VB5000 Manual do Utilizador Página 41
- Página / 124
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
MPEG-2 Configuration
VBrick MPEG-2 Appliance Admin Guide 33
Packet Payload Size Controls the amount of MPEG data within each UDP packet. The
default value is 4136. Since Ethernet networks are limited to a
packet size of 1500 bytes, multiple IP packets are required to span
one UDP packet. When choosing a packet payload size, special
attention must be paid to the network capability and topology. The
allowed range is 1316 to 8872 bytes per packet, even numbers only.
When the MTU is set to the default of 1500, the VBrick appliance
will not produce fragmented UDP packets at or below a payload size
of 1472. Note that MPEG-2 video playback on Vista PCs may be
suboptimal with small packet payload settings.
If you wish to select something other than the default (4136),
VBrick recommends that the Packet Payload Size be a number in the
vicinity of the Actual Transport Rate divided by 800—but no
smaller than 1316 and no larger than 8872. This recommendation
represents a compromise: smaller payloads provide smoother
delivery to the decoder and improve the decoder performance;
larger payloads impose less demand on the encoder processing
capabilities. This recommendation becomes increasingly significant
as the transport bitrate decreases and falls below 3.3 Mbps; 4136 is a
better value for Packet Payload Size when the transport bitrate is 3.3
Mbps or higher. It is also beneficial but not necessary for the Packet
Payload Size to be a multiple of 188.
Note that when you adjust the Packet Payload Size and video Bit
Rate on the encoder, the decoder video may be affected. For
example, when the Packet Payload Size on the encoder is set to 7000
or above and Bit Rate on the Configuration: Encoder > Video page
is set from 1–1.4 Mbps, the decoder receiving the video may go into
a continual reset loop (every 10–60 seconds depending on the
settings). To stop the resetting, set the Bit Rate to 1.5 Mbps or
higher.
Unicast Poll This parameter is used to instruct the VBrick to poll whether the
unicast destination VBrick is configured to accept this stream. If the
unicast destination VBrick is not configured to accept this stream,
this VBrick will not send the stream. This feature is designed to
eliminate unwanted unicast video traffic across the network.
Unicast Ping Feature for primary destination can be enabled, disabled. If the
VBrick is designated to transmit a transport stream to any
destination (whether another VBrick or not) in unicast mode, this
parameter is used to instruct the VBrick to ping the destination
periodically to test connectivity before sending the stream. If
Unicast Ping is not enabled, and the destination goes off-line, the
unicast stream may be broadcast to all destinations causing flooding
on the network. This scenario largely depends on network
architecture and may or may not occur. This feature should only be
disabled if the network has a particular requirement that makes it
unworkable.
- VB4000-5000-6000 Series 1
- Network Video Appliances 1
- Copyright 2
- FCC Notice 2
- About VBrick Systems 2
- Contents 3
- 3. SDI Configuration 4
- 4. Status 4
- 5. Diagnostics 5
- 6. Maintenance 5
- 7. Maintenance Mode 5
- 8. VBStar 5
- MPEG-2 Admin Guide 7
- Font Conventions 8
- Printer-Friendly 8
- Mixed Model Appliances 10
- Introduction 11
- 4 © 2009 VBrick Systems, Inc 12
- MPEG-2 Configuration 13
- Optimizing MPEG-2 Performance 14
- Configuration: Network 16
- Automatic is 18
- Domain Name Server 19
- Network Time Synchronization 19
- Configuration: Billboard 22
- Using the Billboard 23
- Billboard FTP 23
- Billboard URLs 24
- Billboard File Types 24
- Creating a Billboard 25
- Configuration: Decoder 26
- Source-Specific Multicast 28
- Configuration: Encoder 32
- Announce Common Information 43
- 172.22.3.4 but not to 44
- Configuration: Pump 45
- Configuration: Recorder 45
- Configuration: Conferencing 45
- Configuration: Passthrough 46
- Passthrough State: Responder 47
- Passthrough State: Initiator 48
- Configuration: System 50
- Front Panel LCD Display 52
- Improving Security 56
- Run Scripts Using IWS 59
- Sample Script 61
- SDI Configuration 65
- Chapter 4 69
- Status: Network Status 71
- Interface 73
- Status: Decoder Status 74
- Status: Encoder Status 76
- Status: Hard Drive Status 78
- Status: FTP Server Status 81
- Status: System Log 81
- Status: System Log > Traps 82
- Status: User Information 83
- Diagnostics 87
- Refresh, Start/Stop, and 88
- Default to run the test 88
- Trace Route Test Results 89
- Refresh button 90
- Diagnostics: Device Test 91
- Diagnostics: Hard Drive 93
- Maintenance 95
- Write privileges 98
- Usernames & Passwords 99
- Passwords 101
- Maintenance Mode 103
- Maintenance Mode Features 104
- Maintenance Mode Indicators 104
- Chapter 8 107
- VBStar Pump 108
- VBStar Record 113
- FTP Server Enable 116
- VBStar FTP File Transfer 119
- FTP Server 1–8 120
- FTP Status 121
- VBStar Status 122
- VBrick Systems, Inc 124
- 12 Beaumont Road 124
Samson 3710 Усилитель manuales
Manuales del propietario y guías del usuario para Equipo Samson 3710 Усилитель.
Ofrecemos 1 manuales en pdf Samson 3710 Усилитель para descargar gratis por tipos de documentos: Manual de usuario
Comentários a estes Manuais